European Sealing Association
Frenzelit novaphit SSTC TA-L with IB and XP Tech - Printable Version

+- European Sealing Association (https://forum.bacibg.org)
+-- Forum: Flange Gaskets (https://forum.bacibg.org/forumdisplay.php?fid=1)
+--- Forum: Gasket Database (https://forum.bacibg.org/forumdisplay.php?fid=2)
+---- Forum: ESAData Approved Datasheets (https://forum.bacibg.org/forumdisplay.php?fid=10)
+---- Thread: Frenzelit novaphit SSTC TA-L with IB and XP Tech (/showthread.php?tid=83)



Frenzelit novaphit SSTC TA-L with IB and XP Tech - root - 01-06-2020

Approval of Data Import from gasketdata.org

Type: sheet gasket
Publication: 14.01.2013

Material: GR

Link to gasketdata.org


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - IDT - 10-05-2020

Agree with AMTEC's proposal - cross-check leakage at 40 bar and also cross-check of Qsmax at 400°C (seems to be to high in comparison to same material without IB)


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - SGL - 10-05-2020

I agree with AMTEC and IDT: Leakage cross-check at 40 bar and also Qsmax cross-check at 400°C


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - Donit - 10-08-2020

I think that that Pqr values must be provided at 3 different gasket surface stresses.


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - Klinger - 10-09-2020

Standard requires that Pqr is measured at 3 different stresses for each temperature


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - Teadit - 10-12-2020

Agree for three gasket loads at each temperature (PQR)


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - EynardRobin - 10-19-2020

Agree with AMTEC's proposal + add PQR values at 3 different temperatures


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - AVKO - 10-19-2020

(10-08-2020, 03:17 PM)Donit Wrote: I think that that Pqr values must be provided at 3 different gasket surface stresses.

Agree


RE: Frenzelit novaphit SSTC TA-L with IB and XP Tech - AMTEC - 12-11-2020

Cross-checks:

Leakage test @ 40 bar
PQR @ QSmax (180 MPa)/400°C.


Result:
In the leakage cross-check the published leak rates have been confirmed, except the one at the first gasket stress of 5 MPa. Frenzelit agreed to use the leak rates of the cross-check for this stress level to determine the gasket characteristics.

In the PQR test @ 180 MPa/400 °C the sample failed.
Frenzelit was informed about this result and performed PQR double tests at 160 MPa/400 °C. The gasket passed these tests and the PQR values were determined at 0.97. The datasheet is updated with lower QSmax value at 400 °C and with PQR values at 160 MPa/400 °C.