Poll: Do you agree on publishing the data?
You do not have permission to vote in this poll.
Yes
75.00%
6 75.00%
No (Comment in the thread)
0%
0 0%
Yes, but cross-check is required (Specify kind of test in the thread)
25.00%
2 25.00%
Abstain
0%
0 0%
Total 8 vote(s) 100%
* You voted for this item. [Show Results]

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Teadit International TF1590 2.0mm
#1
Thumbs Up 
Approval of Data Import from gasketdata.org

Type: sheet gasket
Publication: 01/02/13

Material: PTFE

Link to gasketdata.org


Attached Files
.pdf   Teadit_TF1590_2mm_v3_ESA Approval_2020-05-20.pdf (Size: 113.35 KB / Downloads: 22)
Reply
#2
According to my experiences the Qsmax value for this gasket material is around 80 MPa at 250°C (without bore intrusion).
I suggest Pqr test at 160 MPa and 250°C.

Maja
Reply
#3
Eg graph @ 250°C looks very unusual for that type of material and very different from the graph of 3,0mm sample of same grade.
I propose x check on Qsamx/Eg @ 250°C.

Stephan
Reply
#4
The following cross-check is recommended:

EG at 250 °C

In the cross-check the divergence was outside the allowable range, see document dated on 2020-09-23. Also in a second cross-check, the deviation was higher than specified in the ESAData spec.

Teadit decided to use the values of the two cross-checks for publication. With the values of these tests the datasheet was updated, see attached document dated on 2020-09-30. The information about bore intrusion was also added.

If nobody has any objections, the datasheet will be accepted.


Attached Files
.pdf   Teadit_TF1590_2mm_v3a_ESA Approval_2020-09-30.pdf (Size: 113.77 KB / Downloads: 2)
.pdf   Teadit_TF1590_2mm_v3_Cross-check_2020-09-23.pdf (Size: 139.97 KB / Downloads: 3)
Reply
#5
(07-20-2020, 12:10 PM)AMTEC Wrote: The following cross-check is recommended:

EG at 250 °C

In the cross-check the divergence was outside the allowable range, see document dated on 2020-09-23. Also in a second cross-check, the deviation was higher than specified in the ESAData spec.

Teadit decided to use the values of the two cross-checks for publication. With the values of these tests the datasheet was updated, see attached document dated on 2020-09-30. The information about bore intrusion was also added.

If nobody has any objections, the datasheet will be accepted.
Agreed.
Reply
#6
(07-20-2020, 12:10 PM)AMTEC Wrote: The following cross-check is recommended:

EG at 250 °C

In the cross-check the divergence was outside the allowable range, see document dated on 2020-09-23. Also in a second cross-check, the deviation was higher than specified in the ESAData spec.

Teadit decided to use the values of the two cross-checks for publication. With the values of these tests the datasheet was updated, see attached document dated on 2020-09-30. The information about bore intrusion was also added.

If nobody has any objections, the datasheet will be accepted.
ok, fine
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)